Contribution of Red Blood Cells and Platelets to Blood Clot Computed Tomography Imaging and Compressive Mechanical Characteristics.

Thrombus computed tomography (CT) imaging characteristics may correspond with thrombus mechanical properties and thus predict thrombectomy success. The impact of red blood cell (RBC) content on these properties (imaging and mechanics) has been widely studied. However, the additional effect of platelets has not been considered. The objective of the current study was to examine the individual and combined effects of blood clot RBC and platelet content on resultant CT imaging and mechanical characteristics. Human blood clot analogues were prepared from a combination of preselected RBC volumes and platelet concentrations to decouple their contributions. The resulting clot RBC content (%) and platelet content (%) were determined using Martius Scarlet Blue and CD42b staining, respectively. Non-contrast and contrast-enhanced CT (NCCT and CECT) scans were performed to measure the clot densities. CECT density increase was taken as a proxy for clinical perviousness. Unconfined compressive mechanics were analysed by performing 10 cycles of 80% strain. RBC content is the major determinant of clot NCCT density. However, additional consideration of the platelet content improves the association. CECT density increase is influenced by clot platelet and not RBC content. Platelet content is the dominant component driving clot stiffness, especially at high strains. Both RBC and platelet content contribute to the clot's viscoelastic and plastic compressive properties. The current in vitro results suggest that CT density is reflective of RBC content and subsequent clot viscoelasticity and plasticity, and that perviousness reflects the clot's platelet content and subsequent stiffness. However, these indications should be confirmed in a clinical stroke cohort.

Evaluation of DNA extracted from residual blood clots after serological testing.

DNA quality is of paramount importance for molecular biology research. This study aimed to assess the DNA extracted from residual blood clots after serological testing, focusing on the impact of blood clot segments, extraction kits, temporary storage durations (TSDs), and thawing methods on DNA quality. We divided the residual blood clot column (BCC) from healthy donors into three segments and utilized two different extraction kits. The BCCs were subjected to four TSDs at 4°C (7 days, 10 days, 1 month, and 2 months) and three thawing methods (4°C, room temperature, and 37°C). We found that the TIANamp Blood Clot DNA Kit yielded consistently high-quality DNA from each segment with stable A260/280 and A260/230 ratios. The DNA yield showed a strong positive correlation with leukocyte concentration, and a satisfactory median DNA yield of 28.79 µg/g BCC was obtained across all segments. DNA integrity, as measured by the DNA integrity number and DNA fragment peak size, decreased with increasing TSD at 4°C, with a notable decrease after 10 days of storage. Thawing at 37°C resulted in the lowest DNA fragment peak size. In conclusion, BCC could be an ideal DNA source with satisfactory yield and purity. A prolonged TSD at 4°C leads to an obvious decrease in DNA integrity, and thawing the frozen BCC at 37°C decreases DNA fragment sizes. To maintain DNA integrity, BCCs should be cryopreserved as soon as possible after short TSDs at 4°C and thawed at 4°C.

Contribution of staphylococcal virulence factors in the pathogenesis of thrombosis.

Staphylococci are responsible for many infections in humans, starting with skin and soft tissue infections and finishing with invasive diseases such as endocarditis, sepsis and pneumonia, which lead to high mortality. Patients with sepsis often demonstrate activated clotting pathways, decreased levels of anticoagulants, decreased fibrinolysis, activated endothelial surfaces and activated platelets. This results in disseminated intravascular coagulation and formation of a microthrombus, which can lead to a multiorgan failure. This review describes various staphylococcal virulence factors that contribute to vascular thrombosis, including deep vein thrombosis in infected patients. The article presents mechanisms of action of different factors released by bacteria in various host defense lines, which in turn can lead to formation of blood clots in the vessels.

Detection of Blood Clots Using a Whole Stent as an Active Implantable Biosensor.

Many cardiovascular problems stem from blockages that form within the vasculature and often treatment includes fitting a stent through percutaneous coronary intervention. This offers a minimally invasive therapy but re-occlusion through restenosis or thrombosis formation often occurs post-deployment. Research is ongoing into the creation of smart stents that can detect the occurrence of further problems. In this study, it is shown that selectively metalizing a non-conductive stent can create a set of electrodes that are capable of detecting a build-up of material around the stent. The associated increase in electrical impedance across the electrodes is measured, testing the stent with blood clot to mimic thrombosis. It is shown that the device is capable of sensing different amounts of occlusion. The stent can reproducibly sense the presence of clot showing a 16% +/-3% increase in impedance which is sufficient to reliably detect the clot when surrounded by explanted aorta (one sample t-test, p = 0.009, n = 9). It is demonstrated that this approach can be extended beyond the 3D printed prototypes by showing that it can be applied to a commercially available stent and it is believed that it can be further utilized by other types of medical implants.

Microfabricated Nitinol Stent Retrievers with a Micro-Patterned Surface.

Stent retrievers are medical devices that are designed to physically remove blood clots from within the blood vessels of the brain. This paper focuses on microfabricated nitinol (nickel-titanium alloy) stent retrievers, which feature micro-patterns on their surface to enhance the effectiveness of mechanical thrombectomy. A thick film of nitinol, which was 20 µm in thickness, was sputtered onto a substrate with a micro-patterned surface, using electroplated copper as the sacrificial layer. The nitinol film was released from the substrate and then thermally treated while folded into a cylindrical shape. In vitro experiments with pig blood clots demonstrated that the micro-patterns on the surface improved the efficacy of blood clot retrieval.

Numerical study of ultra-large von Willebrand factor multimers in coagulopathy.

An excessive von Willebrand factor (VWF) secretion, coupled with a moderate to severe deficiency of ADAMTS13 activity, serves as a linking mechanism between inflammation to thrombosis. The former facilitates platelet adhesion to the vessel wall and the latter is required to cleave VWF multimers. As a result, the ultra-large VWF (UL-VWF) multimers released by Weibel-Palade bodies remain uncleaved. In this study, using a computational model based on first principles, we quantitatively show how the uncleaved UL-VWF multimers interact with the blood cells to initiate microthrombosis. We observed that platelets first adhere to unfolded and stretched uncleaved UL-VWF multimers anchored to the microvessel wall. By the end of this initial adhesion phase, the UL-VWF multimers and platelets make a mesh-like trap in which the red blood cells increasingly accumulate to initiate a gradually growing microthrombosis. Although high-shear rate and blood flow velocity are required to activate platelets and unfold the UL-VWFs, during the initial adhesion phase, the blood velocity drastically drops after thrombosis, and as a result, the wall shear stress is elevated near UL-VWF roots, and the pressure drops up to 6 times of the healthy condition. As the time passes, these trends progressively continue until the microthrombosis fully develops and the effective size of the microthrombosis and these flow quantities remain almost constant. Our findings quantitatively demonstrate the potential role of UL-VWF in coagulopathy.

Case report: Total obstruction of the left main bronchus by a blood clot leads to pneumonectomy in a pregnant woman.

Introduction and importance: Airway obstruction resulting from blood clot formation is observed across various clinical scenarios and is often preceded by hemoptysis. This condition can significantly compromise respiratory function, potentially leading to life-threatening ventilatory distress. Case presentation: In this report, the authors present a case of acute airway obstruction associated with hemoptysis in an 18-week pregnant woman admitted to the emergency department for acute respiratory distress. Clinical and radiographic evidence strongly suggested the presence of an endobronchial blood clot causing focal airway obstruction. Diagnosis was confirmed through direct endoscopic evaluation. Clinical discussion: Initial attempts to remove the obstructing clot from the airway involved lavage, aspiration, and forceps extraction by using a bronchoscope. In cases in which these measures proved ineffective, other management strategies include rigid bronchoscopy, embolization, and surgical resection. Conclusion: Central airway obstruction is a critical condition caused by numerous factors such as tumours or blood clots. Treatment focuses on securing the airway, ensuring breathing, and using tools such as bronchoscopy for diagnosis and treatment. Surgery is considered a last resort when other methods are ineffective.

Fast screening using attenuated total reflectance- fourier transform infrared (ATR-FTIR) spectroscopy of patients based on D-dimer threshold value.

Attenuated Total Reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy is an emerging technology in the medical field. Blood D-dimer was initially studied as a marker of the activation of coagulation and fibrinolysis. It is mainly used as a potential diagnosis screening test for pulmonary embolism or deep vein thrombosis but was recently associated with COVID-19 severity. This study aimed to evaluate the use of ATR-FTIR spectroscopy with machine learning to classify plasma D-dimer concentrations. The plasma ATR-FTIR spectra from 100 patients were studied through principal component analysis (PCA) and two supervised approaches: genetic algorithm with linear discriminant analysis (GA-LDA) and partial least squares with linear discriminant (PLS-DA). The spectra were truncated to the fingerprint region (1800-1000 cm-1). The GA-LDA method effectively classified patients according to D-dimer cutoff (≤0.5 µg/mL and >0.5 µg/mL) with 87.5 % specificity and 100 % sensitivity on the training set, and 85.7 % specificity, and 95.6 % sensitivity on the test set. Thus, we demonstrate that ATR-FTIR spectroscopy might be an important additional tool for classifying patients according to D-dimer values. ATR-FTIR spectral analyses associated with clinical evidence can contribute to a faster and more accurate medical diagnosis, reduce patient morbidity, and save resources and demand for professionals.

Effect of EDTA Activation on Blood Clot Structure in Regenerative Endodontics: A Scanning Electron Microscopy Study.

INTRODUCTION: EDTA plays a crucial role in regenerative endodontic therapy (RET) because of its significant biological effects. However, EDTA is also recognized as the preferred anticoagulant for hematologic tests. Thus, this study aimed to assess the influence of different EDTA activation techniques on the morphology of blood clots after conditioning the root canal dentin. METHODS: Forty extracted human teeth were prepared to simulate immature teeth and divided into the following 5 groups: (1) saline solution (negative control), (2) EDTA 17% + saline solution (CNI), (3) CNI + ultrasonic activation, (4) CNI + Easy clean activation, and (5) CNI + XP-endo Finisher activation. After irrigation, the roots were cleaved, and the root canals were filled with human blood to clot formation. The morphology and density of erythrocytes, platelets, and the fibrin network were observed using a scanning electron microscope. The fibrin network density was classified using a 4-point scale. Data were analyzed using the Friedman test and the Kruskal-Wallis test with Bonferroni adjustment (α = 5%). RESULTS: All groups exhibited consistent blood clot morphology characterized by a high density of erythrocytes, platelets, and white blood cells throughout the entire length of the root canal. The negative control group showed statistically significant high scores of fibrin density compared with the CNI group in all root thirds (P < .05). However, there was no statistical difference in the scores for the fibrin network density between the groups irrigated with EDTA with and without activation (P > .05). CONCLUSIONS: EDTA may impair the fibrin network formation compared with the saline group. However, EDTA activation did not significantly change the effects on the blood clot in contact with the conditioned intraradicular dentin.

Decoding thrombosis through code: a review of computational models.

From the molecular level up to a blood vessel, thrombosis and hemostasis involves many interconnected biochemical and biophysical processes over a wide range of length and time scales. Computational modeling has gained eminence in offering insights into these processes beyond what can be obtained from in vitro or in vivo experiments, or clinical measurements. The multiscale and multiphysics nature of thrombosis has inspired a wide range of modeling approaches that aim to address how a thrombus forms and dismantles. Here, we review recent advances in computational modeling with a focus on platelet-based thrombosis. We attempt to summarize the diverse range of modeling efforts straddling the wide-spectrum of physical phenomena, length scales, and time scales; highlighting key advancements and insights from existing studies. Potential information gleaned from models is discussed, ranging from identification of thrombus-prone regions in patient-specific vasculature to modeling thrombus deformation and embolization in response to fluid forces. Furthermore, we highlight several limitations of current models, future directions in the field, and opportunities for clinical translation, to illustrate the state-of-the-art. There are a plethora of opportunity areas for which models can be expanded, ranging from topics of thromboinflammation to platelet production and clearance. Through successes demonstrated in existing studies described here, as well as continued advancements in computational methodologies and computer processing speeds and memory, in silico investigations in thrombosis are poised to bring about significant knowledge growth in the years to come.

Resonance, Velocity, Dispersion, and Attenuation of Ultrasound-Induced Shear Wave Propagation in Blood Clot In Vitro Models.

OBJECTIVE: Improve the characterization of mechanical properties of blood clots. Parameters derived from shear wave (SW) velocity and SW amplitude spectra were determined for gel phantoms and in vitro blood clots. METHODS: Homogeneous phantoms and phantoms with gel or blood clot inclusions of different diameters and mechanical properties were analyzed. SW amplitude spectra were used to observe resonant peaks. Parameters derived from those resonant peaks were related to mimicked blood clot properties. Three regions of interest were tested to analyze where resonances occurred the most. For blood experiments, 20 samples from different pigs were analyzed over time during a 110-minute coagulation period using the Young modulus, SW frequency dispersion, and SW attenuation. RESULTS: The mechanical resonance was manifested by an increase in the number of SW spectral peaks as the inclusion diameter was reduced (P < .001). In blood clot inclusions, the Young modulus increased over time during coagulation (P < .001). Descriptive spectral parameters (frequency peak, bandwidth, and distance between resonant peaks) were linearly correlated with clot elasticity values (P < .001) with R2 = .77 for the frequency peak, .60 for the bandwidth, and .48 for the distance between peaks. The SW dispersion and SW attenuation reflecting the viscous behavior of blood clots decreased over time (P < .001), mainly in the early stage of coagulation (first minutes). CONCLUSION: The confined soft inclusion configuration favored SW mechanical resonances potentially challenging the computation of spectral-based parameters, such as the SW attenuation. The impact of resonances can be reduced by properly selecting the region of interest for data analysis.

Whole blood coagulation in an ex vivo thrombus is sufficient to induce clot neutrophils to adopt a myeloid-derived suppressor cell signature and shed soluble Lox-1.

BACKGROUND: Blood clots are living tissues that release inflammatory mediators including IL-8/CXCL8 and MCP-1/CCL2. A deeper understanding of blood clots is needed to develop new therapies for prothrombotic disease states and regenerative medicine. OBJECTIVES: To identify a common transcriptional shift in cultured blood clot leukocytes. METHODS: Differential gene expression of whole blood and cultured clots (4 hours at 37 °C) was assessed by RNA sequencing (RNAseq), reverse transcriptase-polymerase chain reaction, proteomics, and histology (23 diverse healthy human donors). Cultured clot serum bioactivity was tested in endothelial barrier functional assays. RESULTS: All cultured clots developed a polymorphonuclear myeloid-derived suppressor cell (PMN-MDSC) signature, including up-regulation of OLR1 (mRNA encoding lectin-like oxidized low-density lipoprotein receptor 1 [Lox-1]), IL-8/CXCL8, CXCL2, CCL2, IL10, IL1A, SPP1, TREM1, and DUSP4/MKP. Lipopolysaccharide enhanced PMN-MDSC gene expression and specifically induced a type II interferon response with IL-6 production. Lox-1 was specifically expressed by cultured clot CD15+ neutrophils. Cultured clot neutrophils, but not activated platelets, shed copious amounts of soluble Lox-1 (sLox-1) with a donor-dependent amplitude. sLox-1 shedding was enhanced by phorbol ester and suppressed by heparin and by beta-glycerol phosphate, a phosphatase inhibitor. Cultured clot serum significantly enhanced endothelial cell monolayer barrier function, consistent with a proresolving bioactivity. CONCLUSION: This study suggests that PMN-MDSC activation is part of the innate immune response to coagulation which may have a protective role in inflammation. The cultured blood clot is an innovative thrombus model that can be used to study both sterile and nonsterile inflammatory states and could be used as a personalized medicine tool for drug screening.

Comparative Evaluation of the Regenerative Potential of Blood Clot and Platelet-rich Fibrin in Young Permanent Teeth Based on the Revised American Academy of Endodontics Clinical Considerations for Regenerative Procedure: 2016.

Aim: To compare and evaluate the regenerative potential of blood clots and platelet-rich fibrin (PRF) in IYNPT based on the revised American Academy of Endodontics (AAE) clinical considerations for regenerative endodontics 2016. Materials and methods: A total of 20 patients (7-12 years) with immature young necrotic permanent teeth were included and irrigation and disinfection were done using the revised AAE protocol. Teeth were randomly categorized into PRF scaffolding and conventional bleeding technique. The cases were followed up for 1, 3, and 6 months for clinical and radiographic evaluation. Result: At 6 months there was no significant difference between the groups in terms of clinical healing and periapical healing. A significant statistical difference was noted at the end of 6 months with respect to apical closure within the PRF group. A significant difference was seen in the increase in dentin thickness between groups with PRF showing more increase. Conclusion: The PRF scaffold can be used as it induces the regenerative potential of stem cells at the apex. How to cite this article: Prakash AJ, Naik SV, Attiguppe P. Comparative Evaluation of the Regenerative Potential of Blood Clot and Platelet-rich Fibrin in Young Permanent Teeth Based on the Revised American Academy of Endodontics Clinical Considerations for Regenerative Procedure: 2016. Int J Clin Pediatr Dent 2023;16(S-2):S149-S154.

Anti-Fibronectin Aptamer Modifies Blood Clot Pattern and Stimulates Osteogenesis: An Ex Vivo Study.

BACKGROUND: Scaffold (SCA) functionalization with aptamers (APT) provides adsorption of specific bioactive molecules on biomaterial surfaces. The aim of this study was to observe if SCA enriched with anti-fibronectin APT can favor coagulum (PhC) and osteoblasts (OSB) differentiation. METHODS: 20 µg of APT was functionalized on SCA by simple adsorption. For PhC formation, SCAs were inserted into rat calvaria defects for 17 h. Following proper transportation (buffer solution PB), OSBs (UMR-106 lineage) were seeded over PhC + SCAs with and without APT. Cells and PhC morphology, PhC cell population, protein labeling and gene expression were observed in different time points. RESULTS: The APT induced higher alkaline phosphatase and bone sialoprotein immunolabeling in OSB. Mesenchymal stem cells, leukocytes and lymphocytes cells were detected more in the APT group than when scaffolds were not functionalized. Additionally, an enriched and dense fibrin network and different cell types were observed, with more OSB and white blood cells in PhC formed on SCA with APT. The gene expression showed higher transforming growth factor beta 1 (TGF-b1) detection in SCA with APT. CONCLUSIONS: The SCA functionalization with fibronectin aptamers may alter key morphological and functional features of blood clot formation, and provides a selective expression of proteins related to osteo differentiation. Additionally, aptamers increase TGF-b1 gene expression, which is highly associated with improvements in regenerative therapies.

Early Blood Clot Detection Using Forward Scattering Light Measurements Is Not Superior to Delta Pressure Measurements.

The occurrence of thrombus formation within an extracorporeal membrane oxygenator is a common complication during extracorporeal membrane oxygenation therapy and can rapidly result in a life-threatening situation due to arterial thromboembolism, causing stroke, pulmonary embolism, and limb ischemia in the patient. The standard clinical practice is to monitor the pressure at the inlet and outlet of oxygenators, indicating fulminant, obstructive clot formation indicated by an increasing pressure difference (ΔP). However, smaller blood clots at early stages are not detectable. Therefore, there is an unmet need for sensors that can detect blood clots at an early stage to minimize the associated thromboembolic risks for patients. This study aimed to evaluate if forward scattered light (FSL) measurements can be used for early blood clot detection and if it is superior to the current clinical gold standard (pressure measurements). A miniaturized in vitro test circuit, including a custom-made test chamber, was used. Heparinized human whole blood was circulated through the test circuit until clot formation occurred. Four LEDs and four photodiodes were placed along the sidewall of the test chamber in different positions for FSL measurements. The pressure monitor was connected to the inlet and the outlet to detect changes in ΔP across the test chamber. Despite several modifications in the LED positions on the test chamber, the FSL measurements could not reliably detect a blood clot within the in vitro test circuit, although the pressure measurements used as the current clinical gold standard detected fulminant clot formation in 11 independent experiments.

Management of a Large Post-tonsillectomy Thrombus Obstructing the Laryngeal View: A Case Report.

Anesthetic management of children with a post-tonsillectomy hemorrhage can be challenging. The patients may be anemic and hypovolemic and are at increased risk of having a difficult airway due to active bleeding, vomiting, and anatomical issues. A clot may also interfere with viewing the larynx, further exacerbating the difficulty of intubation. We describe a pediatric post-tonsillectomy hemorrhage case complicated by a large obstructing clot that was removed with Magill forceps after the airway was successfully secured with an endotracheal tube during rapid sequence induction.

FastSkin® Concept: A Novel Treatment for Complex Acute and Chronic Wound Management.

Successful treatments for acute and chronic skin wounds remain challenging. The goal of this proof-of-concept study was to assess the technical feasibility and safety of a novel wound treatment solution, FastSkin®, in a pig model. FastSkin® was prepared from skin micrografts patterned in blood using acoustic waves. Upon coagulation, the graft was transferred on a silicone sheet and placed on wounds. Six full-thickness wounds were created at the back of two pigs and treated with either FastSkin®, split-thickness skin graft (positive control), a gauze coverage (negative control, NC1), or blood patterned without micrografts (negative control, NC2). Silicone sheets were removed after 7, 14, and 21 days. Wound healing was monitored for six weeks and evaluated macroscopically for re-epithelialization and morphometrically for residual wound area and wound contraction. Tissue regeneration was assessed with histology after six weeks. Re-epithelialization was faster in wounds covered with FastSkin® treatments compared to NC2 and in NC2 compared to NC1. Importantly, an enhanced collagen organization was observed in FastSkin® in contrast to NC treatments. In summary, two clinically approved skin wound treatments, namely micrografting and blood clot graft, were successfully merged with sound-induced patterning of micrografts to produce an autologous, simple, and biologically active wound treatment concept.

A comparative clinico-radiographic analysis of regenerative endodontic procedure on immature necrotic permanent teeth using blood clot and PRF as scaffold: A retrospective study.

Objectives: To evaluate the clinical and radiographic success rate of blood clot and platelet rich fibrin (PRF) as a scaffold system in regenerative endodontic procedure in immature traumatized necrotic teeth.. Materials and methods: This retrospective study examined the records of 28 subjects with necrotic immature open apex due to trauma treated with blood clot or PRF as a scaffold in regenerative endodontic procedure. The disinfection was carried out with calcium hydroxide as an intra-canal medicament. The clinical outcome was recorded using a binary variable of presence or absence of pain and intra-oral swelling. The radiographic outcome was recorded for periapical healing using Ørstavik's Periapical Index and apical response using Chen and Chen index. Comparison of frequencies of categories of variables with groups was done using the chi-square test. The pairwise comparison of time intervals was done using Wilcoxon Signed Ranks Test. Results: Intra-group comparison of pain and intra-oral swelling had highly significant (p = 0.000) results for both groups over a period of 12 months. Inter-group comparison for clinical outcomes was insignificant. For the radiographic outcome, there was a statistically non-significant difference for periapical healing and apical response for both intra-group and inter-group comparisons. Conclusion: Both PRF and blood clot have a favourable outcome for a regenerative endodontic procedure with a disinfectant protocol using calcium hydroxide as intracanal medicament. Considering the cumbersome procedure involved in procuring PRF scaffold, especially in children, inducing bleeding can be considered a recommended method for a regenerative endodontic procedure.

Liver Clot after Periodontal Surgery: A Rare Case Report.

Due to the primary closure of the fragile tissues, large postoperative drainage is unexpected following a periodontal medical procedure. This case study elaborately illustrates the formation of a "liver coagulation" or "currant jam clot" following a periodontal fold surgical operation. Contamination, internal damage, and the presence of foreign particles such as bone splinters or bits of dental restorative dressing can all increase the risk of an incident happening.

The Effect of Blood Clots on the Quality of RNA Extracted from PAXgene Blood RNA Tubes.

Background: PAXgene® Blood RNA tubes are routinely used in clinical research and molecular biology applications to preserve the stability of RNA in whole blood. However, in practice, blood clots are occasionally observed after blood collection and are often ignored. Currently, there are few studies on whether blood clots affect the quality of RNA extracted from these tubes. Materials and Methods: Fifteen pairs of nonclot and clot PAXgene Blood RNA tube samples (n = 30) were collected to form two matched groups from 15 patients. According to the maximum diameter (d) of the blood clot observed visually at the time of sample reception, the clot groups were divided into a small-clot group (0 cm < d < 0.5 cm) and a large-clot group (d ≥ 0.5 cm). RNA was extracted by the PAXgene Blood RNA Kit. To analyze the quality of RNA, its yield and purity were assessed by spectrophotometry, and integrity was measured by microfluidic electrophoresis. An A260/280 ratio between 1.8 and 2.2 indicated purified RNA, and RNA integrity number (RIN) values ≥7.0 were considered to represent qualified integrity. Results: The median yields of RNA from the nonclot and clot groups were 3.84 (2.80-6.38) µg and 4.87 (2.77-8.30) µg, respectively. The median A260/280 ratios were 2.08 (2.06-2.09) and 2.09 (2.07-2.11), whereas the median A260/230 ratios were 1.77 (1.31-1.91) and 1.67 (1.21-1.94) in the two groups. In addition, the median RINs were 8.20 (8.00-8.40) and 7.20 (6.60-7.70), respectively. There were no significant differences in RNA yields, A260/280, or A260/230 between the two groups. However, the RIN value of the clot group was significantly lower compared with the nonclot group (p < 0.05), with RIN ≥7.0 found in all nonclot samples and 60% of clot samples (p < 0.05). Furthermore, in the clot groups, the small-clot samples had higher RIN values than large-clot samples (8.25 [7.75-8.75] vs. 6.90 [6.60-7.30], p < 0.001). Conclusions: The formation of large blood clots in PAXgene Blood RNA tubes will reduce the integrity of extracted RNA.